Strutconfigurator
System · trapeze bracket

Trapeze bracket builder: from rod to containment

A trapeze bracket is two threaded rods with one or more channel beams between them. Easy to draw, easy to miscount. The configurator does the counting for you, including every nut, washer and channel nut.

Short answer

A trapeze bracket consists of two threaded rods from the soffit with one to four strut channel beams between them, the tiers. Each tier carries a cable tray, ladder or basket. You set the width, the spacing between tiers, the rod size and the drop; the configurator turns it into a bill of materials.

Trapeze bracket builder: from rod to containment1,400600710Threaded rod M102 × per bracketCable ladder 500×1008 × 5G16Cable basket 400×60Cat6A × 48 · OM4 × 18Strut 41×41×2.5HDGViewFrontScale1:20
trapeze bracketOwn drawing · to scale
  • Hosting Data stored in the EU · Frankfurt Stored with Neon (eu-central-1) · runs on the Cloudflare network
  • Privacy GDPR Data processing agreement available
  • System Brand-independent Public version · client version on your own range
  • Built by Built by NEXTRIQ 5.0 on Google · 22 reviews

What does a trapeze bracket consist of?

Every trapeze uses the same parts. The difference lies in sizes and quantities, and that is where quoting often goes wrong: one channel nut or washer short per joint means a second delivery.

  • Two threaded rods per bracket (M8, M10 or M12), with a ceiling anchor, beam clamp or hanger bracket
  • A strut channel beam per tier, usually 41×41
  • A nut and washer above and below the beam at each joint
  • End caps and, where needed, hold-down clamps for the containment

How wide and how high should a trapeze be?

The beam is wider than the containment: allow the tray width plus room for the rods and clamps either side. Tier spacing follows from the containment depth and the room needed to pull cables; in data centres 300 mm between tiers is a common rule of thumb. The drop is the distance from the soffit to the lowest tier.

Example from the configurator
PartSizeQty per bracket
Threaded rod M101,350 mm2
Strut 41×41×2.5 HDG1,400 mm2 (2 tiers)
Hex nut M10–8
Washer M10–8
Ceiling anchor M10–2

Which threaded rod size do you need?

That follows from the total load per bracket: the weight of containment and cables over the support spacing, shared by two rods. Work out the load per rod with our threaded rod load tool, then check the anchor and the soffit. The configurator calculates loads indicatively; the manufacturer confirms at quotation.

How to build a trapeze bracket in 5 steps

  1. Choose application and environment. Sector, location (soffit, steelwork, shaft) and environment. The configurator suggests the finish.
  2. Set tiers and width. Choose 1 to 4 tiers, the beam width and the spacing between tiers.
  3. Choose the suspension. Threaded rod M8, M10 or M12, the drop and the fixing: anchor, beam clamp or bracket.
  4. Add containment and cables. A cable tray, ladder or basket per tier, with the cables inside and the fill ratio.
  5. Download or send an enquiry. Bill of materials, cutting list and drawing as PDF, or an enquiry that reaches a supplier.

Frequently asked questions

What is a trapeze type support?

A support made of two threaded rods with one or more beams between them, carrying cable trays, ladders, baskets or pipes. Also called a trapeze bracket or trapeze hanger.

How many tiers can a trapeze have?

One to four in the configurator. More tiers mean more load per rod; check the rod, the anchor and the soffit.

What is a typical spacing between trapeze brackets?

Often 1.2 to 1.5 m for cable tray and basket, as a rule of thumb. The containment and load decide; the containment manufacturer gives the permitted span.

Is the trapeze builder free?

Yes. Configuring and the PDF with bill of materials, cutting list and drawing are free for installers.

Next step

See your own range in 3D.

In 30 minutes we show how your installers configure, what arrives on your side and what the client version on your range involves.

Manufacturer or wholesaler

Book a demo with Ismail

You see the configurator in your own brand and we discuss your range, systems and markets.

Reply from Ismail within one working day

Installer

Configure for free

A trapeze, frame or tray with cables in a few minutes, with a bill of materials and drawing.

Enquiry goes to a supplier · reply within one working day