Strutconfigurator
System · strut channel cut to length

Strut channel cut to length

The C-channel with inturned lips that almost every support is built on. In the configurator you choose channel, gauge, finish and length, and see the cutting list straight away.

Short answer

Strut channel is a 41 mm wide steel C-section with a 22 mm slot opening in which channel nuts lock. Common depths are 21, 41, 62 and 82 mm, supplied in 3 or 6 m lengths. Cutting to length before delivery saves installation time and offcuts on site.

Strut channel cut to length41214141418241×2141×4141×82 back-to-back1,350Saw cut50 mm stepsSlot 28×14back slotsSection41 mmLengthL ≤ 6.000
strut channel cut to lengthOwn drawing · to scale
  • Hosting Data stored in the EU · Frankfurt Stored with Neon (eu-central-1) · runs on the Cloudflare network
  • Privacy GDPR Data processing agreement available
  • System Brand-independent Public version · client version on your own range
  • Built by Built by NEXTRIQ 5.0 on Google · 22 reviews

What sizes of strut channel are there?

Every common system uses a 41 mm width and a 22 mm slot opening. Depth sets the stiffness: 41×21 for light supports and clamps, 41×41 as the standard beam, and 41×62 or 41×82 for longer spans. Two channels welded back to back form a double channel for heavy beams and uprights.

Common channels
ChannelThickness (mm)LengthsWeight 41×41 (kg/m)
41×211.5 · 2.0 · 2.53 and 6 m–
41×411.5 · 2.0 · 2.53 and 6 m2.46 to 2.88
41×622.0 · 2.53 and 6 m–
41×82 back-to-back2.53 and 6 m–

Source: size tables from three manufacturers (brand-independent standard catalogue, 19/11/2026). Weight: range across finishes.

How much load does a 41×41 strut channel carry?

That depends on the span and the deflection you accept. Over short spans strength sets the limit; over longer spans deflection governs. Always read both columns.

41×41×2.5 slotted, indicative
Span (mm)Max. UDL (kN)Load at L/360 deflection (kN)
5008.03–
1,0004.012.66
1,5002.681.18
2,0002.000.66
3,0001.33–

Source: Atkore UK (Unistrut), "Beam Loading" table, 41×41 slotted, uniformly distributed load. Indicative; the manufacturer of your channel confirms.

Which finish should you choose?

Pre-galvanised is the standard for dry indoor areas. Hot-dip galvanised (HDG, 45 to 55 µm on channel, to EN ISO 1461) is for outdoor, damp and industrial areas. Stainless steel 304 or 316 is used in food, pharma, chemical and marine settings. The configurator suggests a finish in the first step, based on sector and environment; you can always override it.

How does cut-to-length work in the configurator?

You enter the length in 50 mm steps. The configurator puts every piece on the cutting list and nests the pieces on 6 m lengths, so you see how many full lengths and how much offcut you need. End caps are chosen per piece.

  • Channel, gauge and back slots (plain or 28×14 slots)
  • Length in 50 mm steps
  • Finish: pre-galvanised, HDG, stainless 304 or 316
  • Cutting list optimised on 6 m and a bill of materials as PDF

Frequently asked questions

Is there a difference between strut and Unistrut?

It is the same type of channel. Strut channel is the generic name; Unistrut is one manufacturer's brand name. The configurator is brand-independent.

Is slotted channel weaker than plain channel?

Slightly. The back slots remove a few per cent of the section. Load tables therefore list slotted and plain values separately. Always use the table of the manufacturer of your channel.

What lengths can you get strut channel in?

Standard lengths are 3 and 6 m. In the configurator you cut to length in 50 mm steps; the cutting list nests on 6 m lengths.

Which channel nut goes with 41×21 channel?

A short spring channel nut or a plain nut. For 41×41 and deeper channels use a long spring nut, so it stays in place during installation.

Next step

See your own range in 3D.

In 30 minutes we show how your installers configure, what arrives on your side and what the client version on your range involves.

Manufacturer or wholesaler

Book a demo with Ismail

You see the configurator in your own brand and we discuss your range, systems and markets.

Reply from Ismail within one working day

Installer

Configure for free

A trapeze, frame or tray with cables in a few minutes, with a bill of materials and drawing.

Enquiry goes to a supplier · reply within one working day