Strutconfigurator
Data centres and telecom

Data centre cable management, from the soffit down

Above every row of racks hang several routes: power, copper and fibre, each on its own tier. Strutconfigurator puts the supports, containment and cables into one configuration, with a bill of materials per bracket.

Short answer

Data centre cable management starts above the racks: trapeze brackets with two to four tiers, carrying cable basket for data and fibre and cable ladder for power. Keep power and data segregated, check the fill ratio per tier and the load per threaded rod, and have the manufacturer confirm every load.

Data centre cable management, from the soffit downcold aisleData and fibrebasket, lower tierPowerladder, upper tier600SectionData hallRoute2 tiers
Data centres and telecomOwn drawing · to scale
  • Hosting Data stored in the EU · Frankfurt Stored with Neon (eu-central-1) · runs on the Cloudflare network
  • Privacy GDPR Data processing agreement available
  • System Brand-independent Public version · client version on your own range
  • Built by Built by NEXTRIQ 5.0 on Google · 22 reviews

Why does data centre cable management start above the racks?

Because density and change are built into the brief. The Netherlands had more than 1.5 GW of IT capacity in data centres at the end of 2025 (Dutch Data Center Association, 2026). In Amsterdam, 927 MW was operational in Q2 2026, with 102 MW under construction and 251 MW planned (Cushman & Wakefield). Growth is moving to locations such as Eemshaven and Middenmeer. Every new hall means hundreds of brackets, and every bracket a bill of materials.

How should you divide the tiers?

A common layout puts power on a cable ladder on one tier and copper and fibre in cable baskets on another, with 300 mm between tiers as a rule of thumb. Fibre gets its own run where possible, so heavy cables do not press on it. Above the cold aisle, keep space clear for sprinklers and lighting.

Example layout per row of racks
TierContainmentCablesWatch
TopCable ladder 500×100Power 5G16Rungs for tying, room for heat
MiddleCable basket 400×60Cat6A S/FTPFill max. 40% at installation
BottomCable basket 300×60OM4 and OS2 trunksOwn tier, protection at bends

How do you keep power and data segregated?

With separate tiers or a divider in the containment, following the applicable IEC and national standards. The configurator shows a red status when power and data share a run without a divider. The enquiry still goes through, with a clear warning for the job preparer.

What does a trapeze above the racks carry?

The load per bracket is the weight of all containment and cables per metre, multiplied by the support spacing, shared over two threaded rods. Then check the rod, the anchor or beam clamp and the soffit. The configurator calculates this indicatively per bracket; the manufacturer confirms at quotation. Where circuit integrity in fire is required, tested systems and lower loads apply; check them with the manufacturer.

Why prefabrication in data centres?

Data centre builders increasingly work offsite, because fitters are scarce and programmes are tight. Trapezes and frames are assembled in a workshop and delivered per position on pallets. That needs a drawing and bill of materials per position: exactly what the configurator produces.

Frequently asked questions

Which containment is used for data cables in a data centre?

Usually cable basket above the racks: light, open and easy to adapt. For heavy power cables over longer spans, choose cable ladder.

How much space should you leave between tiers?

300 mm as a rule of thumb, so cables can be laid and air can move around them. Soffit height, sprinklers and lighting set the final dimension.

Can fibre share containment with power?

Electrically yes, fibre is immune to interference. Mechanically it is a risk: heavy cables can kink or crush fibre. Give fibre its own tier or run where possible.

Can the configurator deliver prefab brackets per position?

The configurator produces a drawing, bill of materials and cutting list per position. Assembly is done by your workshop or an assembly partner.

Next step

See your own range in 3D.

In 30 minutes we show how your installers configure, what arrives on your side and what the client version on your range involves.

Manufacturer or wholesaler

Book a demo with Ismail

You see the configurator in your own brand and we discuss your range, systems and markets.

Reply from Ismail within one working day

Installer

Configure for free

A trapeze, frame or tray with cables in a few minutes, with a bill of materials and drawing.

Enquiry goes to a supplier · reply within one working day