Unistrut channel sizes all start from the same 41 mm width, then vary by depth, gauge and slot pattern. On UK sites “Unistrut” has become shorthand for any strut channel, so it helps to know what the part numbers actually describe. This guide lists the sizes, weights and suffixes, then answers the questions installers ask most: solid or slotted, which lengths, and how to cut it.
Unistrut is a registered trademark of Atkore for a metal framing system of cold-formed C-channel with inturned, serrated lips that grip a spring channel nut. Atkore traces P1000 back to 1924 and describes a system that needs no welding or drilling [1]. Strutconfigurator is brand-independent and is not a dealer or partner of Atkore or any other manufacturer.
What are the standard Unistrut channel sizes?
| Part | Width × depth × gauge (mm) | Type | Weight (kg/m) |
|---|---|---|---|
| P1000 | 41 × 41 × 2.5 | plain (solid back) | 2.65–2.88 |
| P1000T | 41 × 41 × 2.5 | 28×14 back slots | 2.46–2.73 |
| P1100T | 41 × 41 × 2.0 | 28×14 back slots | 2.11–2.18 |
| P2000T | 41 × 41 × 1.5 | 28×14 back slots | 1.59–1.72 |
| P3300 | 41 × 21 × 2.5 | plain | 1.82–1.91 |
| P3300T | 41 × 21 × 2.5 | 28×14 back slots | 1.57–1.76 |
| P3100 | 41 × 21 × 2.0 | plain | 1.65 |
| P4000 | 41 × 21 × 1.5 | plain | 1.24 |
| P5500 | 41 × 62 × 2.5 | plain | 3.42 |
| P5000 | 41 × 83 × 2.5 | plain | 4.22–4.63 |
| P3301 | 41 × 42, 2× P3300 | back-to-back | 3.53–3.76 |
| P1001 | 41 × 82, 2× P1000 | back-to-back | 5.51–5.77 |
| P5501T | 41 × 124, 2× P5500 | back-to-back, slotted | 6.99–8.50 |
| P5001 | 41 × 165, 2× P5000 | back-to-back | 9.27 |
Manufacturer data [2]. The weight range covers different finishes and lengths. The 83 mm deep section is also sold as 41×82.
A 41 mm channel has a slot opening of 22 mm [3]. Standard fittings have 14 mm holes for M12 bolts, which is why one spanner builds the whole frame.
What do the letters after the part number mean?
| Code | Meaning | Source |
|---|---|---|
| T | 28×14 mm slots in the back | [2] |
| T10 | 25×11 mm slots in the back | [2] |
| TTT | Slotted on three faces | [2] |
| PG | Pre-galvanised | [1][2] |
| HG | Hot-dip galvanised | [1][2] |
| ZP | Electro-galvanised (zinc plated) | [2] |
| PO | Plain, untreated | [2] |
| DF | Defender, the manufacturer’s own coating | [2] |
| SS | Stainless steel | [1] |
Codes as used on the Atkore UK and Vergokan product pages.
The pitch of the back slots is not stated on the pages we read. 50 mm centres are common; confirm with the supplier if fittings must land on fixed positions.
Is solid Unistrut stronger than slotted?
Yes, by a small margin. The slots remove steel from the back, and that costs stiffness more than strength.
| Channel (2.5 mm) | Max. uniform load at 1,000 mm span (kN) | Max. load at L/360 deflection (kN) | Iy (cm⁴) |
|---|---|---|---|
| 41×41 solid (P1000) | 4.336 | 3.149 | 7.21 |
| 41×41 slotted (P1000T) | 4.012 | 2.659 | 6.10 |
| 41×21 solid (P3300) | 1.354 | 0.520 | 1.19 |
| 41×21 slotted (P3300T) | 1.288 | 0.455 | 1.04 |
Manufacturer data: total uniform load on a simply supported beam [1]. Indicative; the manufacturer confirms.
Slots cost 5 to 8% of load capacity and 12 to 16% of stiffness (calculated from the table). Choose slotted channel when you want freedom to fix anywhere on site. Choose solid where deflection governs, such as long spans under heavy cable ladder.
What lengths can you get Unistrut in?
Standard bars are 3 m and 6 m, and some types are also available in 2 m [2]. Anything else is cut to length. If you order many identical pieces, ask your supplier to cut them: it saves site time and offcuts. The cut-to-length channel module in the configurator turns your lengths into a cutting list optimised on 6 m bars.
Which finishes and standards apply in the UK?
Atkore UK states that its channel complies with BS 6946, the British standard for metal channel cable support systems, and that each batch carries a traceable Quality Batch Number. P1000 is also offered in an FR version tested for two hours’ fire resistance to EN 1363-1:2020 on the ISO 834 standard curve [1]. Finishes:
- Pre-galvanised (PG): dry indoor areas.
- Hot-dip galvanised (HG): outdoors, damp and industrial areas; 45–55 µm zinc on strut [3].
- Electro-galvanised (ZP): indoors, mainly small parts.
- Stainless 304 and 316 (SS): hygienic, chemical and marine areas.
For the trade-offs, see pre-galvanised vs hot-dip galvanised vs stainless. If you manage product data, Vergokan classifies these channels under ETIM class EC000082 [2].
How do you cut Unistrut to length?
Use a bandsaw or cold saw for a square, burr-free cut. An angle grinder works but burns off zinc over a wider band. Deburr the end, fit an end cap where people can walk into it, and touch up the cut with zinc-rich paint in damp locations. Check the length before you cut: 41×41 slotted weighs 2.73 kg/m, so a 6 m bar is about 16 kg to handle at height (calculated).
How much weight can Unistrut channel hold?
It depends on the span and the deflection you accept. As an indication, slotted 41×41 at a 1,500 mm span carries 2.68 kN in total, falling to 2.13 kN if you limit deflection to L/200 [1]. That is the channel; the rods, nuts and anchors need their own check. The strut load calculator reads the same manufacturer tables, and 41×21 vs 41×41 strut channel compares the two common sizes in detail.
Where do these figures come from?
- Atkore UK, product pages P1000, P1000T, P3300 and P3300T (description, BS 6946, QBN traceability, FR version, Beam Loading and Section Properties tables). Accessed 19-11-2026. https://www.atkore.com/en-gb/products/metal-framing-and-fittings/P1000 · https://www.atkore.com/en-gb/products/metal-framing-and-fittings/P1000T · https://www.atkore.com/en-gb/products/metal-framing-and-fittings/P3300 · https://www.atkore.com/en-gb/products/metal-framing-and-fittings/P3300T
- Vergokan (part of Atkore), Unistrut channel product pages: dimensions, gauge, weight per finish, T, T10 and TTT codes, ETIM class. Accessed 19-11-2026. https://www.vergokan.com/nl/kabeldraagsystemen/Montagesystemen/Unistrut+profielen___montagerails/P1000T · https://www.vergokan.com/nl/kabeldraagsystemen/Montagesystemen/Unistrut+profielen___montagerails/P1000T10
- Eurostrut, 41×41 mm slotted channel, hot-dip galvanised (22 mm slot, serrated lips, 45 to 55 µm zinc). Accessed 19-11-2026. https://eurostrut.com/montageprofiel-41x41mm-met-gaten-3m-tv/ES1000THDG3M
Frequently asked questions
What are the standard strut channel sizes?
The 41 mm system dominates: 41×21, 41×41, 41×62 and 41×83 mm single channel, in 2.5 mm gauge and for some sizes 2.0 or 1.5 mm. Back-to-back versions give 41×42, 41×82, 41×124 and 41×165 mm.
Is solid Unistrut stronger than slotted?
Slightly. At a 1,000 mm span, solid 41×41 (P1000) carries an indicative 4.34 kN uniform load against 4.01 kN for slotted P1000T. The bigger difference is stiffness: at an L/360 deflection limit the slotted section carries about 15% less (manufacturer data; the manufacturer confirms).
What lengths can you get Unistrut in?
Standard lengths are 3 m and 6 m, and some types are also stocked in 2 m. Anything else is cut to length, either on site or by the supplier. The configurator sets lengths in 50 mm steps and builds a cutting list from 6 m bars.
Is there a difference between strut and Unistrut?
Strut is the generic product; Unistrut is a registered brand of Atkore. Many manufacturers make 41 mm channel with a 22 mm slot opening, so fittings often fit. Published loads only apply to the combination the manufacturer has tested.
https://strutconfigurator-site.pages.dev/en/knowledge-base/unistrut-channel-sizes/ · Updated 19 November 2026 · Indicative; the manufacturer confirms.