MPO trunk cables carry 12, 24 or more fibres from rack to rack in one slim cable. In a data hall a single trunk replaces dozens of individual patch leads, and you notice the difference in the containment straight away. For the person planning the route, the choice comes down to four questions: which connector, which polarity, what length and where it runs. This guide works through each one.
What is an MPO trunk cable?
MPO stands for multi-fibre push-on: one rectangular ferrule carrying 8 to 24 fibres in one or two rows. The connector family is defined in IEC 61754-7 [1]. MTP is one manufacturer’s registered trademark for a connector that is compatible with MPO.
A trunk is terminated at both ends in the factory and arrives tested. Nothing is spliced on site: the cable is laid and plugged in. That makes installation quick and predictable, provided the length is right. In a data hall with hundreds of fibre links, the gain is mostly time and space: one 6 mm MPO-12 trunk replaces six separate duplex links (diameter indicative).
Which MPO connectors and trunk types are there?
| Connector | Fibres | Typical use |
|---|---|---|
| MPO-8 (Base-8) | 8 | Parallel optics with 4 transmit and 4 receive fibres |
| MPO-12 | 12 | The most common trunk; 6 duplex links through a cassette, or 100GBASE-SR4 using 8 of the 12 fibres [2] |
| MPO-16 | 16 | Applications with 8 transmit and 8 receive fibres |
| MPO-24 | 24 | High density; 12 duplex links |
Application data; overview indicative.
The assemblies differ as well:
- Trunk: MPO at both ends, for the backbone between racks or halls.
- Fan-out or harness: MPO at one end and individual LC duplex connectors at the other, for direct connection to equipment.
- Cassette and trunk: the trunk plugs into the back of a cassette with LC ports on the front, so patching uses standard LC leads.
Choose the fibre type too. OM4 multimode is for distances within the hall, up to 100 m at 100GBASE-SR4 [2]. OS2 singlemode is for longer runs. Common jacket colours are aqua or violet for OM4 and yellow for OS2 (rule of thumb, check with the supplier).
How do polarity and pinning work?
The transmit fibre at one end has to arrive at a receive fibre at the other. With twelve fibres in one connector, that takes planning. The TIA-568 series defines three polarity methods [3]:
| Method | Trunk | Fibre 1 arrives at | Consequence |
|---|---|---|---|
| A | Key up to key down | Fibre 1 | Flip in a patch cord at one end |
| B | Key up to key up | Fibre 12 | Same cassettes at both ends |
| C | Pair-wise flipped | Fibre 2 | Flip is inside the trunk |
Based on the polarity methods in the TIA-568 series [3].
The rule that matters most: pick one method for the whole project and write it into the specification. Trunks, cassettes and patch cords must all match.
Then pinning. A mated pair always consists of one pinned (male) and one unpinned (female) connector. Decide for the project which side carries the pins, for example the cassettes and transceivers, and order trunks and patch cords to suit.
What loss should you allow per link?
TIA-568.3 allows a maximum of 0.75 dB per mated connector pair [3]. Manufacturers’ low-loss connectors come in below that. For each link, add up every mated pair plus the fibre attenuation over the length, and compare the total with the loss budget of the application. High-speed multimode applications have tight budgets, so fewer mated pairs per link gives you more margin. Test every link after installation and hand over the test results.
How do you measure trunk length?
A trunk cannot be shortened, so measure along the route:
- Horizontal length along the containment, including bends and level changes.
- Drop at each end, from the containment to the top of the rack.
- Rack entry at each end, to the cassette or panel.
- Allowance of 3 to 5% (rule of thumb, indicative).
Round up to the supplier’s length increment. A worked example with three links is in custom length data cables.
What mistakes come up most with MPO trunks?
- Two polarity methods mixed. A method B trunk with method A cassettes gives links where transmit and receive do not line up. Fix one method.
- Two pinned connectors. A mated pair always has one male and one female connector. Two males will not mate properly and can damage the pins.
- Ordered too short. A trunk can only be extended with an extra mated pair, and every mated pair costs loss.
- Dirty end faces. An MPO connector packs many fibres into a small area. Inspect and clean every connector before plugging in.
- Pulling on the connector. Always pull with the sock, never on the connector or the bare cable.
How should a trunk be laid in the containment?
- Own basket or tier. Keep fibre apart from copper and power so it never ends up under heavy cables. See Cat6A vs fibre.
- Pulling sock. Pull with the protective sock over the connectors, never by the connector itself.
- Bend radius. As a rule of thumb 10 times the cable diameter unloaded and 20 times while pulling (indicative). The datasheet governs.
- Bundling. Hook-and-loop ties only, never pulled tight.
- Drop-out. Bring the trunk into the rack over a waterfall, with no sharp edges.
- Slack. Coil spare length neatly in the rack or a storage tray, with a generous loop.
In the configurator you add MPO trunks in OM4 or OS2 in the Cables step, with length, connectors at both ends and a label. They appear as separate lines in the bill of materials, next to the containment and supports.
Where do these figures come from?
- IEC 61754-7, Fibre optic interconnecting devices and passive components. Fibre optic connector interfaces. Part 7: Type MPO connector family.
- IEEE 802.3bm, 100GBASE-SR4 over multimode (8 of 12 fibres, up to 100 m on OM4).
- TIA-568.3-D, Optical Fiber Cabling and Components Standard (polarity methods A, B and C; maximum 0.75 dB per mated connector pair).
- Bend radius, allowance and jacket colours: common practice (rule of thumb, indicative). The datasheet and the specification govern.
Frequently asked questions
What is the difference between MPO and MTP?
MPO is the connector family defined in IEC 61754-7. MTP is one manufacturer's registered trademark for an MPO-compatible connector. They mate with each other; the differences lie in mechanical design and the manufacturer's own specification.
Which MPO polarity method should I use?
The TIA-568 series describes three methods: A, B and C. Pick one for the whole project and write it into the specification. Trunks, cassettes and patch cords must all match that method.
Can an MPO trunk be cut to length on site?
No. A trunk is terminated and tested in the factory. Measure along the route before ordering and add a small allowance (3 to 5% as a rule of thumb, indicative). Coil any slack neatly in the rack.
What insertion loss should I allow for an MPO connection?
TIA-568.3 allows up to 0.75 dB per mated connector pair. Manufacturers' low-loss connectors come in below that. Add up every mated pair and the fibre length in a link and compare with the loss budget of the application.
https://strutconfigurator-site.pages.dev/en/knowledge-base/mpo-mtp-trunk-cables/ · Updated 19 November 2026 · Indicative; the manufacturer confirms.