# Data centre cable management: routes, trays and cabling

URL: https://strutconfigurator-site.pages.dev/en/knowledge-base/data-centre-cable-management/
Topic: Data centres and prefab · Author: Ismail Yeşilay · Last updated: 2026-11-19

> Plan data centre cable management in three layers: the route (overhead or under a raised floor), the containment (cable basket, tray or ladder on trapeze brackets) and the cables themselves. Keep power and data segregated, check fill and load tier by tier, and have the manufacturer confirm every load figure before you order.

Most guides on data centre cable management stop at the rack: patch panels, vertical managers and colour-coded leads. This one starts at the soffit. Before a single patch lead goes in, someone has to decide where the containment runs, how many tiers hang from each trapeze, what each tier carries and whether the fixings can take it. Good data centre cable management is mostly decided at that point, so here is how a site engineer or MEP designer works through it.

## Why does data centre cable management start above the racks?

Because density and change are built into the brief. The Netherlands alone had more than 1.5 GW of IT capacity at the end of 2025 [1], and Amsterdam had 927 MW operational with 102 MW under construction and 251 MW planned [2]. Halls at that scale carry dozens of runs per row, stacked in tiers.

Three things set a data hall apart from an office fit-out:

- **Density.** Hundreds of cables per row, on several tiers.
- **Change.** Racks are added and re-cabled while the hall is live, so every tier must stay accessible.
- **Segregation.** Power, copper and fibre each have their own requirements. A mistake in the build-up is very hard to correct in a live hall.

## Overhead or underfloor: which route works best?

Both are in use. Cooling strategy, floor void depth and the expected rate of change decide it.

| Factor | Overhead containment | Raised floor void |
|---|---|---|
| Access | From steps or a tower, everything visible | Lift tiles, limited overview |
| Cooling | No effect on an underfloor air plenum | Cables obstruct air if the void is the supply plenum |
| Expansion | Add tiers to the same trapeze | Limited by void depth |
| Loads | Into the soffit or steelwork | Into the slab, via floor supports |
| Typical use | Fibre and copper, often power too | Power and legacy halls |

*Rule of thumb, indicative. The hall design decides.*

If the route goes underfloor, see [raised access floor cabling](https://strutconfigurator-site.pages.dev/en/knowledge-base/raised-access-floor-cabling/).

## What goes on each tier?

A common build-up uses three tiers on one trapeze bracket: fibre, copper and power. Each tier has its own containment, so each service can grow without disturbing the others.

| Tier | Height above floor (example) | Containment | Services |
|---|---:|---|---|
| 1 | 2,700 mm | Cable basket 300×55 mm | Fibre: MPO trunks and LC patching |
| 2 | 3,000 mm | Cable basket 600×55 mm | Copper: Cat6A |
| 3 | 3,300 mm | Cable ladder 450×100 mm | Power |

*Example build-up at 300 mm tier spacing (rule of thumb, indicative). Rack height, soffit height, sprinklers and lighting set the real dimensions. Basket depths of 30, 55 and 106 mm are common in the UK [3].*

Keep 150 to 300 mm clear above the top tier for cable laying (rule of thumb, indicative). Bring cables down into the rack over a waterfall or drop-out so they do not kink over the edge of the basket.

## How do you segregate power and data?

In the UK, BS 7671 regulation 528.1 covers the proximity of Band I circuits (data and telecoms) to Band II circuits (low-voltage power) [5]. For electromagnetic separation, BS EN 50174-2 is the reference [6]. It makes the minimum separation depend on three things: the segregation classification of the data cable, the number and type of power circuits, and the type of separation (free air, open or perforated metal containment, or a solid metal divider).

On site that usually comes down to one of three options:

1. **Separate tiers** for power and data. The most generous option and the easiest to extend.
2. **A divider** in a shared tray where space is tight.
3. **Fibre** wherever the design allows, since it is immune to interference.

There is more in [segregating power and data cables](https://strutconfigurator-site.pages.dev/en/knowledge-base/power-data-cable-segregation/).

## How many cables fit in one basket?

Add up the cross-section of every cable and divide by the cross-section of the containment. Aim for 40% on a new installation and stay below 60% (rule of thumb, indicative). That leaves room for heat, for pulling in and for future cables.

Example: a 300×55 mm basket has a nominal 16,500 mm². At 40%, 6,600 mm² is available. A 7.5 mm Cat6A U/FTP cable (indicative) takes 44.2 mm², so about 149 cables fit.

Check the manufacturer's usable cross-section for wire basket. A 100×600 mm basket is listed at 53,076 mm² usable rather than 60,000 mm² nominal [4]. The full method is in [cable tray fill calculation](https://strutconfigurator-site.pages.dev/en/knowledge-base/cable-tray-fill-calculation/).

## What load does each support carry?

Work out the weight per metre for each tier, multiply by the support centres and add the tiers together. A worked example for one full data tier:

| Item | Value | Source |
|---|---:|---|
| Cable basket 600×100 mm, hot-dip galvanised | 3.09 kg/m | Manufacturer data [4] |
| 480 × Cat6A U/FTP at about 0.06 kg/m | 28.8 kg/m | Rule of thumb, indicative [8] |
| Total per metre | 31.9 kg/m | Calculated |
| Support centres for basket | 1.5 m | Rule of thumb, indicative |
| Load per support | about 47.8 kg, 0.47 kN | Calculated |
| 41×41×2.5 mm slotted channel, 1,000 mm span | 4.01 kN max. uniformly distributed load | Manufacturer data [7] |

*Loads are indicative; the manufacturer confirms.*

With three tiers like this, one trapeze carries about 1.4 kN, or about 0.7 kN per drop rod. Each cross-member only carries its own tier, and a 41×41 channel at 1,000 mm span handles 0.47 kN comfortably. The limiting link is then usually the studding, the anchor or the soffit itself. See [threaded rod load table](https://strutconfigurator-site.pages.dev/en/knowledge-base/threaded-rod-load-table/). Check each of those separately against manufacturer data.

## How do you build it faster on site?

A row of racks repeats itself dozens of times, which makes the containment a natural fit for offsite manufacture. Trapezes are cut and assembled in a workshop, labelled by grid position and simply hung on the drop rods on site. See [prefabricated trapeze brackets](https://strutconfigurator-site.pages.dev/en/knowledge-base/prefabricated-trapeze-brackets/).

Put the data cabling in the same request. Once the route is fixed, so is the length of every link, and fibre trunks and copper can be made to length. See [custom length data cables](https://strutconfigurator-site.pages.dev/en/knowledge-base/custom-length-data-cables/).

In the configurator you build the trapeze tier by tier, choose the containment per tier and add the cables. It shows the fill per tray and flags power and data sharing a tray without a divider. The bill of materials, cutting list and drawing come out as a PDF.

## Where do these figures come from?

1. Dutch Data Center Association, *State of the Dutch Data Centers 2026*, reported by Dutch IT Channel (11 September 2026). https://www.dutchitchannel.nl/research/759815/nederland-blijft-europese-zwaargewicht-in-datacenterbouw
2. Cushman & Wakefield, *EMEA Datacentre Update* (2026). https://www.cushmanwakefield.com/nl-nl/netherlands/news/2026/04/emea-datacentre-update-h2-2025
3. Atkore UK, steel wire cable tray product pages (30, 55 and 106 mm deep). Accessed 19 November 2026. https://www.atkore.com/en-gb/products/cable-management-systems/MC55
4. Eurostrut, product page for 100×600 mm hot-dip galvanised wire basket: usable cross-section 53,076 mm², 3.09 kg/m. Accessed 19 November 2026. https://eurostrut.com/rejiband-draadgoot-100x600-hdg/60233600
5. BS 7671, *Requirements for Electrical Installations* (IET Wiring Regulations), regulation 528.1.
6. BS EN 50174-2, *Information technology. Cabling installation. Installation planning and practices inside buildings*.
7. Atkore UK, product page for 41×41×2.5 mm slotted channel, Beam Loading table. Accessed 19 November 2026. https://www.atkore.com/en-gb/products/metal-framing-and-fittings/P1000T
8. Cable diameters and weights: typical datasheet values (rule of thumb, indicative). The datasheet of the chosen cable governs.

## Frequently asked questions

**How much space should you leave between containment tiers above the racks?**

Allow 300 mm between tiers as a rule of thumb (indicative). That leaves room for a hand to lay cables and keeps air around them. Soffit height, sprinkler heads and lighting set the final dimension.

**Which containment is used for data cabling in a data centre?**

Steel cable basket is the usual choice above the racks for copper and fibre: light, open and easy to modify on site. Heavy power cables over longer spans tend to go on cable ladder or solid-bottom cable tray.

**Can fibre share a tray with power cables?**

Electrically yes, because fibre is immune to electromagnetic interference. Mechanically it is a risk: heavy power cables can crush or kink fibre. Give fibre its own tier or raceway and protect it at bends and drops.

**How heavy is a fully loaded cable basket?**

A 600×100 mm basket carrying 480 Cat6A cables weighs about 32 kg per metre: 3.09 kg/m of basket (manufacturer data) plus about 0.06 kg/m per cable (rule of thumb, indicative). At 1.5 m support centres that is roughly 0.47 kN per support.

## Configure it yourself

https://strutconfigurator-app.pages.dev/?lang=en&systeem=trapeze

---

Source: https://strutconfigurator-site.pages.dev/en/knowledge-base/data-centre-cable-management/ · Last updated: 2026-11-19 · Loads are indicative; the manufacturer confirms.
Strutconfigurator is part of NEXTRIQ (Rotterdam).
