# Cat6A vs fibre: what goes where in the containment

URL: https://strutconfigurator-site.pages.dev/en/knowledge-base/cat6a-vs-fibre-containment/
Topic: Data cables · Author: Ismail Yeşilay · Last updated: 2026-11-19

> Use Cat6A up to 100 m and wherever devices draw power over the cable (PoE), such as access points and cameras. Use fibre for longer distances, backbones and high-density links between racks. Fibre takes far less space per link in the containment and ignores interference, though it needs protection from crushing and tight bends.

Cat6A vs fibre is usually framed as a network decision, yet it lands on the containment designer's desk too. The choice decides how far each link can run, whether devices take power over the cable and how much basket you need. For the route itself that last point matters most: copper is thick, heavy and sensitive to interference, fibre is thin, light and fragile. Here are the differences side by side, when to use which and what each means for the containment.

## How do Cat6A and fibre compare?

| Feature | Cat6A (copper) | Fibre OM4 (multimode) | Fibre OS2 (singlemode) |
|---|---|---|---|
| Typical location | Desks, access points, cameras, in-rack | Within the hall, between racks and rows | Between halls, buildings, campus |
| Reach | 100 m channel, 10GBASE-T [1][2] | 100 m at 100GBASE-SR4 [3] | 10 km at 100GBASE-LR4 [3] |
| Power over the cable | Yes, PoE up to 90 W at the switch [4] | No | No |
| Diameter | 7.5–8.0 mm | 2.0 mm patch, 6.0 mm MPO-12 trunk | 2.0 mm patch, 6.0 mm MPO-12 trunk |
| Sensitive to interference | Yes | No | No |
| Connector | RJ45 | LC, MPO | LC, MPO |

*Diameters: rule of thumb, indicative (typical datasheet values).*

## When is Cat6A the right choice?

Cat6A is the default for anything within 100 m that has a network port. Its big advantage is power over the same cable. With PoE to IEEE 802.3bt the switch delivers up to 90 W per port [4], enough for access points, cameras, access control and lighting control without a separate supply. In a data hall, Cat6A is mostly found within the rack and between neighbouring racks, for example from a top-of-rack switch to the servers. Links between rows and to the main distribution area are usually fibre.

Watch the heat with PoE. Data cables carrying power warm up, and large bundles run hotter than loose cables. ISO/IEC TS 29125 deals with this effect [5], so keep bundles small and lay them loose in open basket.

Cat6A comes as U/FTP (foil around each pair) and S/FTP (foil around each pair plus an overall braid). S/FTP is slightly larger and heavier, and the better choice on routes shared with a lot of power cabling.

## When is fibre the right choice?

Choose fibre for distance, bandwidth and density:

- **Distance.** Anything over 100 m, such as links between halls, floors and buildings. OS2 reaches 10 km at 100GBASE-LR4 [3].
- **Backbone and data hall.** Between racks and the main distribution area. OM4 carries 100 Gbit/s over 100 m [3].
- **Density.** MPO trunks put many links into one slim cable. See [MPO/MTP trunk cables](https://strutconfigurator-site.pages.dev/en/knowledge-base/mpo-mtp-trunk-cables/).
- **Interference.** Fibre is immune to electromagnetic fields, so it can run close to power.

OM4 or OS2? Choose OM4 for short links within the hall, where multimode optics are enough. Choose OS2 for runs over 100 m, between buildings, or where the fibre has to outlast several generations of equipment. If in doubt on a backbone, run both in the same basket: an extra trunk takes very little room.

## How much containment space does each need?

For the support system, this is the biggest difference. A worked example for 72 links:

| Option | Cables | Area per cable | Total |
|---|---:|---:|---:|
| Cat6A U/FTP, 7.5 mm | 72 | 44.2 mm² | 3,181 mm² |
| MPO-12 trunk, 6.0 mm (6 duplex links per trunk) | 12 | 28.3 mm² | 339 mm² |

*Calculated with π/4 × d²; diameters rule of thumb, indicative.*

At 40% fill the copper needs about 8,000 mm² of containment, for example a 150×55 mm basket. The fibre fits in a 100×30 mm basket with room to spare. Weight differs as much: 72 Cat6A cables weigh about 4.3 kg per metre (rule of thumb, indicative), twelve trunks a fraction of that. The method is in [cable tray fill calculation](https://strutconfigurator-site.pages.dev/en/knowledge-base/cable-tray-fill-calculation/).

## What does each mean for the containment?

| Point | Cat6A | Fibre |
|---|---|---|
| Segregation from power | Yes, to BS EN 50174-2 and BS 7671 528.1 [6][7] | Only mechanical, against crushing |
| Bend radius | 4 to 8 × d | 10 × d unloaded, 20 × d while pulling |
| Weight | Drives support centres | Low |
| Drop into the rack | Waterfall with a generous radius | Waterfall, no sharp edges |
| Bundling | Small bundles, hook-and-loop ties | Hook-and-loop ties, never pulled tight |

*Bend radius: rule of thumb, indicative. The cable datasheet governs.*

Never secure fibre with tightly pulled cable ties. They squeeze the cable and increase attenuation. Use hook-and-loop ties. More on separation in [power and data cable segregation](https://strutconfigurator-site.pages.dev/en/knowledge-base/power-data-cable-segregation/).

## What mistakes come up most with copper and fibre?

The same mistakes appear on site again and again. Most of them are avoidable at the design stage:

- **Fibre at the bottom of a copper basket.** Every extension adds copper on top. A few years later the fibre sits under the weight of hundreds of cables.
- **Cable ties pulled tight on fibre.** The tie squeezes the jacket and attenuation rises. Use hook-and-loop ties.
- **Tight drops into the rack.** A kink over the basket edge harms copper and fibre alike. Plan a waterfall at every rack.
- **PoE in one big bundle.** Cables carrying power warm up. Spread them over smaller bundles in open basket.
- **Copper beyond 100 m.** A Cat6A channel stops at 100 m [1]. If a rack sits further from the comms room, plan fibre or an extra distributor.
- **No room to grow.** Keep fill at 40% at handover (rule of thumb, indicative) so cables can be added later.

## How do you combine both on one route?

Most projects need both. A practical build-up above a row of racks:

1. **Fibre** in its own narrow basket, so it never ends up under the copper.
2. **Cat6A** in a wider basket alongside or above, with room to grow.
3. **Power** on a separate tier, at a distance from the copper.

In the configurator you add cables per tray, copper and fibre mixed or separated. It shows the fill per tray and flags power and data sharing a tray without a divider. The cables can then be made to length, see [custom length data cables](https://strutconfigurator-site.pages.dev/en/knowledge-base/custom-length-data-cables/).

## Where do these figures come from?

1. ISO/IEC 11801-1, *Information technology. Generic cabling for customer premises. Part 1: General requirements* (Class EA, 100 m channel).
2. IEEE 802.3an, 10GBASE-T over balanced copper cabling.
3. IEEE 802.3bm (100GBASE-SR4 over multimode) and IEEE 802.3ba (100GBASE-LR4 over singlemode).
4. IEEE 802.3bt, Power over Ethernet up to 90 W at the power sourcing equipment (Type 4).
5. ISO/IEC TS 29125, *Telecommunications cabling requirements for remote powering of terminal equipment*.
6. BS EN 50174-2, *Information technology. Cabling installation. Installation planning and practices inside buildings*.
7. BS 7671, *Requirements for Electrical Installations* (IET Wiring Regulations), regulation 528.1.
8. Cable diameters, weights and bend radii: typical datasheet values (rule of thumb, indicative). The datasheet of the chosen cable governs.

## Frequently asked questions

**How far can Cat6A run?**

A Cat6A channel is limited to 100 m: 90 m of fixed cabling plus 10 m of cords (ISO/IEC 11801-1). Over that distance 10GBASE-T delivers 10 Gbit/s. Beyond 100 m, use fibre.

**Can fibre share a cable basket with copper?**

Yes. Fibre is immune to electromagnetic interference. The concern is weight: copper bundles and power cables can crush it. In data centres fibre usually gets its own basket, tier or dedicated raceway.

**How much space does fibre save in the containment?**

A 6 mm MPO-12 trunk takes 28.3 mm² and carries 12 fibres, enough for 6 duplex links. Six 7.5 mm Cat6A cables take 265 mm² together. Per link that is more than nine times less space (diameters indicative).

**What is the minimum bend radius for fibre cable?**

As a rule of thumb 10 times the cable diameter with no load and 20 times while pulling (indicative). For Cat6A it is 4 to 8 times the diameter. The cable datasheet governs.

## Configure it yourself

https://strutconfigurator-app.pages.dev/?lang=en&systeem=kabels

---

Source: https://strutconfigurator-site.pages.dev/en/knowledge-base/cat6a-vs-fibre-containment/ · Last updated: 2026-11-19 · Loads are indicative; the manufacturer confirms.
Strutconfigurator is part of NEXTRIQ (Rotterdam).
