# Cable ladder vs cable tray vs cable basket: which to use

URL: https://strutconfigurator-site.pages.dev/en/knowledge-base/cable-ladder-vs-cable-tray-vs-basket/
Topic: Ladder and basket · Author: Ismail Yeşilay · Last updated: 2026-11-19

> Use cable ladder for heavy power cables and long spans, cable tray for mixed cables that need continuous support or mechanical protection, and cable basket for data, fibre and light power. Cable weight, achievable support centres, environment and any fire-rating requirement decide which system fits a given route.

Cable ladder vs cable tray is the first question on most containment layouts, with cable basket as the third option, now common for data cabling. All three carry cables from A to B, yet each one suits a different kind of route. The choice sets your support centres, the number of trapezes, how easy it is to add cables later and how well the cables shed heat. Below: the three side by side, the UK duty ratings, and a selection guide in five questions.

## What is the difference between cable ladder, cable tray and cable basket?

| Feature | Cable ladder | Cable tray | Cable basket |
|---|---|---|---|
| Construction | Two side rails with rungs | Folded sheet, perforated or solid | Welded wire mesh with safety edge |
| Common depths (UK) | 100, 110, 125, 150 mm side rail | 12/18, 25, 50, 100 mm | 30, 55, 106 mm |
| Common widths | 100–1,000 mm | 50–900 mm | 50–600 mm |
| Lengths | 3 m and 6 m | 3 m | 3 m |
| Support centres | 3 m | 1.5 m | 1.5 m |
| Best for | Heavy power, long runs | Mixed cables, mechanical protection | Data, fibre, light power |
| Ventilation | Very open | Depends on perforation | Open |

*Sizes and lengths: manufacturer data [2][3][4]. Support centres and use: rule of thumb, indicative.*

The biggest practical difference is span. Ladder side rails bridge wider support centres, so you need fewer trapezes. Tray and basket need a support roughly every 1.5 m. See [cable tray supports](https://strutconfigurator-site.pages.dev/en/knowledge-base/cable-tray-supports/) for spacing and couplers.

## What duty ratings does UK cable tray come in?

UK ranges are sold by duty, and the duty mostly tracks the flange depth:

| Duty | Depth | Widths | Length |
|---|---:|---|---:|
| Light duty | 12 mm (50–225 wide), 18 mm (300–900 wide) | 50–900 mm | 3 m |
| Medium duty | 25 mm | 50–900 mm | 3 m |
| Heavy duty | 50 mm | 50–900 mm | 3 m |
| Extra heavy duty | 100 mm | 100–900 mm | 3 m |

*Manufacturer data [2]. Finishes: pre-galvanised, hot-dip galvanised and stainless steel.*

Light-duty tray suits short drops and light cabling. For main runs on trapezes, heavy-duty tray is the usual choice because the deeper flange stiffens the section. The duty also applies to the fittings: bends, tees and risers come in the same duty as the straight lengths, so specify it once for the whole route.

## When should you use cable ladder?

Choose ladder for weight and span. Heavy power cables, single cores in trefoil and long runs through risers and plant rooms belong on ladder.

| Side rail | Range description | Lengths |
|---:|---|---|
| 100 mm and 110 mm | Medium duty | 3 m and 6 m |
| 125 mm | Heavy duty | 3 m and 6 m |
| 150 mm | Extra heavy duty | 3 m and 6 m |

*Manufacturer data [3]. On flat bends, rungs alternate up and down at spacings no greater than 300 mm [3].*

Continental ranges use 60, 100 and 150 mm side rails, with rung centres of 250 mm on the 60 mm ladder and 300 mm on the others [4]. Single-core power cables are held with cable cleats, which are tested under IEC 61914, including for short-circuit forces [6].

## When is cable basket the better choice?

Choose basket for low weight and flexibility on site. Fitters cut it with bolt croppers into bends, tees and reducers without dedicated fittings, which is why it is common in data centres and ceiling voids. It also suits office and hospital ceiling voids, where routes change often and the cable mix is mostly data.

Three points to check:

- **Usable cross-section.** The wire construction makes it smaller than width × depth. One manufacturer lists 53,076 mm² usable for a 100×600 mm basket, against 60,000 mm² nominal [5].
- **Earth continuity.** With the right couplers, continuity is assured to IEC 61537 [5]. Where a section is interrupted, bridge it with a 12 or 16 mm² bonding connector [5].
- **Finish.** UK basket comes electro-zinc, pre-galvanised, powder-coated, zinc-aluminium or hot-dip galvanised [3].

Fixing details are in [cable basket fixing](https://strutconfigurator-site.pages.dev/en/knowledge-base/cable-basket-fixing/).

## Which containment do I need?

Work through these five questions. The first one with a clear answer usually decides it.

1. **How heavy are the cables?** Heavy power or single cores: ladder. Data and fibre: basket. Mixed: tray or basket, with [segregation of power and data](https://strutconfigurator-site.pages.dev/en/knowledge-base/power-data-cable-segregation/).
2. **How far apart can supports be?** If fixing points are scarce, as in a riser or a high-bay hall: ladder.
3. **Do the cables need protection?** Impact risk, visible runs or UV: solid tray with a lid.
4. **What environment?** Indoors and dry: pre-galvanised. Outdoors or damp: hot-dip galvanised. Coastal, chemical or food: stainless steel 316.
5. **Is circuit integrity in a fire required?** Then only a system with a test report. See [fire rated cable tray](https://strutconfigurator-site.pages.dev/en/knowledge-base/circuit-integrity-e30-e90/).

## What mistakes come up most when choosing?

- **Basket for heavy power.** A full basket with large power cables needs many supports. Ladder spans the same distance with fewer.
- **Solid tray for many power cables.** Cables in a closed tray lose heat less easily. Choose perforated tray or ladder where cables run warm.
- **Ladder for thin data cables.** Small cables sag between the rungs. Put them in basket.
- **Mixed materials.** Galvanised fixings in stainless containment corrode in damp conditions. Use fixings in the same material as the containment.
- **No room for bends.** Wide ladder needs a large bend radius. Check space at junctions and crossings early.

## How wide should the containment be?

Width follows from fill. Add up the cable cross-sections, divide by 40% (rule of thumb, indicative) and pick the next size up. The method is in [cable tray fill calculation](https://strutconfigurator-site.pages.dev/en/knowledge-base/cable-tray-fill-calculation/).

In the configurator you choose ladder, tray or basket per tier, in the sizes above. Bends, couplers and supports go into the same bill of materials.

## Where do these figures come from?

1. IEC 61537 (BS EN 61537), *Cable management. Cable tray systems and cable ladder systems*.
2. Atkore UK, cable tray product pages (light, medium, heavy and extra heavy duty). Accessed 19 November 2026. https://www.atkore.com/en-gb/products/cable-management-systems/TUHLT
3. Atkore UK, cable ladder U10, U11, U12, U15 and flat bend product pages, and steel wire cable tray 30, 55 and 106 mm. Accessed 19 November 2026. https://www.atkore.com/en-gb/products/cable-management-systems/U10FB · https://www.atkore.com/en-gb/products/cable-management-systems/MC106
4. Eurostrut, ECL cable ladder product pages (60, 100, 150 mm; rung centres 250 and 300 mm). Accessed 19 November 2026. https://eurostrut.com/kabeldraagsystemen/ecl-kabelladders/
5. Eurostrut, wire basket product pages (100×600 usable 53,076 mm², bonding connector 12 and 16 mm²). Accessed 19 November 2026. https://eurostrut.com/kabeldraagsystemen/pemsa-rejiband-draadgoten/
6. IEC 61914, *Cable cleats for electrical installations*.

## Frequently asked questions

**What is the difference between cable tray and cable basket?**

Cable tray is folded sheet steel, perforated or solid, supporting cables across the full width. Cable basket is a welded steel wire mesh. It is lighter, more open and easy to cut on site into bends, tees and reducers.

**When should you use cable ladder instead of tray?**

For heavy power cables, long runs and wide support centres, such as plant rooms, risers and industrial sites. Heavy-duty ladder with 125 or 150 mm side rails is designed for long spans where supports are hard to install (manufacturer data).

**What depths does UK cable basket come in?**

30, 55 and 106 mm deep are common in the UK, in widths from 50 to 600 mm and 3 m lengths (manufacturer data). Continental ranges often use 35, 60 and 100 mm instead.

**Is cable tray stronger than cable basket?**

It depends on the product, so compare the safe working load at your support centres. Each manufacturer publishes that figure under IEC 61537, so a like-for-like comparison is always possible.

## Configure it yourself

https://strutconfigurator-app.pages.dev/?lang=en&systeem=goot

---

Source: https://strutconfigurator-site.pages.dev/en/knowledge-base/cable-ladder-vs-cable-tray-vs-basket/ · Last updated: 2026-11-19 · Loads are indicative; the manufacturer confirms.
Strutconfigurator is part of NEXTRIQ (Rotterdam).
