# Beam clamp guide: types, flange thickness and loads

URL: https://strutconfigurator-site.pages.dev/en/knowledge-base/beam-clamp-guide/
Topic: Fixings · Author: Ismail Yeşilay · Last updated: 2026-11-19

> A beam clamp fixes threaded rod or strut channel to steel without drilling or welding. Choose by flange thickness, load and direction. A universal M10 beam clamp grips 1 to 25 mm flanges with a 4,500 N working load; a bent strut clamp manages 1,000 N. Strutconfigurator adds the chosen clamp to the bill of materials.

A **beam clamp** is how you hang services from structural steel without touching the steel itself. In warehouses, data halls and car parks, nearly every trapeze hanger ends at a steel beam. The choice looks minor, yet the clamp is often the component with the lowest working load in the whole hanger. This guide helps you pick the right type and fit it properly.

A *beam clamp*, also called a girder clamp, grips the flange of a steel beam and carries threaded rod, a bolt or strut channel. It holds by clamping force, usually with a hardened cone point screw that bites into the flange, so there is no drilling or welding [1].

## What types of beam clamp are there?

| Type | How it works | Typical use |
|---|---|---|
| Universal beam clamp M10 | Clamps the flange; rod hangs below | Single drop rod for a trapeze, pipe or tray |
| Wide-mouth universal clamp | As above, for thicker flanges | Heavy sections with flanges up to 31.8 mm |
| External strut clamp with cone point screw | Wraps the flange and holds a 41 mm channel | Channel across or along the beam |
| Internal strut clamp | Sits inside the channel and clamps the flange | Channel tight to the flange, neat finish |
| Z clamp | Z-shaped clamp over the flange edge | Light fixings to narrow flanges |
| U-bolt clamp | Draws channel or back-to-back section onto the beam | Heavy cross members on beams |

*Overview based on the Eurostrut, Vergokan and Atkore UK ranges [1][2][3].*

## What working load does each beam clamp carry?

| Type (one manufacturer) | Permitted working load | Flange range |
|---|---:|---|
| Internal 41 mm clamp with M10 cone point screw (also for 82×41) | 4,550 N | n/g |
| Universal beam clamp M10, zinc plated | 4,500 N | 1–25 mm |
| Internal 41 mm clamp | 3,600 N | n/g |
| 41 mm clamp, single hole | 2,700 N | n/g |
| Z beam clamp | 2,700 N | n/g |
| Universal clamp with thread M10 | 2,500 N | 1–20.6 mm |
| External 41 mm clamp with M10 cone point screw | 2,300 N | n/g |
| 82 mm clamp with M10 cone point screw | 2,200 N | n/g |
| Wide-mouth universal clamp M10 | 2,200 N | 1–31.8 mm |
| Internal 41 mm clamp with M10 cone point screw | 2,000 N | n/g |
| Bent 41 mm clamp, single slot | 1,000 N | n/g |
| Clamp with M10 stud nut | 1,000 N | n/g |

*Manufacturer data, Eurostrut [1], permitted working load per type. Indicative; the manufacturer confirms. n/g = not given on the product page.*

The spread is wide: the strongest clamp carries four and a half times the lightest (calculated). Compare that with M10 grade 4.8 rod at an indicative 9.3 kN [4]. The clamp almost always sets the limit of the hanger.

## Which beam clamp fits your flange?

Measure first. Flange thickness decides which universal clamp fits: 1 to 25 mm, 1 to 20.6 mm, or 1 to 31.8 mm for the wide-mouth version [1]. For strut clamps, the channel width counts as well: 41 mm, 82 mm or back-to-back [1].

Check the flange shape. Modern UK sections such as UB and UC have parallel flanges. Older RSJs and taper-flange channels do not, and a clamp without a suitable jaw can tilt on them under load. On tapered flanges, use a clamp the manufacturer states is suitable for them.

## How do you choose a beam clamp in four steps?

1. **Survey the steel.** Flange thickness, flange width, and whether the flange is parallel or tapered.
2. **Work out the load per clamp.** Take the weight of containment, cables and hanger per trapeze, divide by the number of clamps and add a margin. Compare with the working load above.
3. **Check the direction.** A clamp hanging straight below the beam is loaded differently from one pulling sideways or at an angle. The rated load applies to the direction the manufacturer states.
4. **Choose finish and approvals.** Zinc plated for dry interiors, hot-dip galvanised or stainless elsewhere. For sprinkler pipework, confirm which listing the designer or insurer needs [1].

## Why not drill or weld the steelwork?

A hole in a flange weakens the beam where it works hardest. It also breaks the coating: the corrosion protection and, where present, the intumescent fire protection. Drilling or welding therefore needs the structural engineer's sign-off. A beam clamp leaves the frame intact and can be moved later, which is why it is the default.

## What should you watch during installation?

- **Tighten the cone point screw properly.** The point must bite into the flange. Lock it with the lock nut afterwards. The torque is in the installation instructions.
- **Repair the coating.** Where the cone point breaks paint or zinc, touch it up in damp locations.
- **Keep off the edge.** Position the clamp as far onto the flange as it will go.
- **Lock against vibration.** Near pumps, fans or air handling units, lock every nut.
- **Two clamps per channel.** Channel hung across a beam gets a clamp on each side so it cannot rock (rule of thumb, indicative).

## How do you hang a trapeze from structural steel?

Where beams run across the containment route, hang each trapeze straight off two universal clamps and drop rods. Where beams run parallel to the route, or their spacing does not suit the support centres, first fix a 41 mm channel across two beams, then hang the trapezes from that channel at the spacing you need. The rest of the assembly is in [how to assemble a trapeze bracket](https://strutconfigurator-site.pages.dev/en/knowledge-base/assemble-trapeze-bracket/). For concrete soffits, see [ceiling anchors for threaded rod](https://strutconfigurator-site.pages.dev/en/knowledge-base/ceiling-anchors-for-threaded-rod/).

## Where do these figures come from?

1. Eurostrut, beam clamp product pages: permitted working load, flange range, FM and VdS approval on universal M10 clamps. Accessed 19-11-2026. https://eurostrut.com/universele-balk-klem-m10-eg/ESP10 · https://eurostrut.com/universele-balk-klem-brede-opening-m10-eg/BTKM10 · https://eurostrut.com/universele-balk-klem-met-draad-m10-eg/TKNM10 · https://eurostrut.com/balkklem-41mm-extern-met-kegelpunt-bout-m10-hdg/ES1271HDG · https://eurostrut.com/balkklem-intern-41mm-met-kegelpunt-bout-m10-hdg/ES2489HDG · https://eurostrut.com/balkklem-gebogen-41mm-1-sleufgat-hdg/ES711HDG
2. Vergokan (part of Atkore), I-beam clamps for 21, 41 and 83 mm channel. Accessed 19-11-2026. https://www.vergokan.com/nl/kabeldraagsystemen/Montagesystemen/Unistrut+montagehulpstukken/P1796
3. Atkore UK, beam clamp P1386, angle beam clamp P1796 and beam clamp P2785. Accessed 19-11-2026. https://www.atkore.com/en-gb/products/metal-framing-and-fittings/P1386 · https://www.atkore.com/en-gb/products/metal-framing-and-fittings/P1796 · https://www.atkore.com/en-gb/products/metal-framing-and-fittings/P2785
4. Strutconfigurator, [threaded rod load table M6 to M20](https://strutconfigurator-site.pages.dev/en/knowledge-base/threaded-rod-load-table/): formula using the tensile stress area from ISO 898-1.

## Frequently asked questions

**How much weight can a beam clamp hold?**

Across one manufacturer's range, permitted working loads run from 1,000 to 4,550 N, roughly 100 to 460 kg. A universal M10 beam clamp reaches 4,500 N and an external strut clamp with a cone point screw 2,300 N. Always use the rating of the exact clamp you install; the manufacturer confirms.

**What is the difference between a beam clamp and a girder clamp?**

In practice none. Girder clamp is the older UK term, often used for heavier clamps on large steel sections. Both grip a flange and carry a rod, bolt or channel without drilling the steel.

**Can I drill the steel instead of using a beam clamp?**

Only with the structural engineer's approval. A hole weakens the member and breaks the corrosion protection and any fire protection coating. A beam clamp leaves the structure intact, which is why it is standard practice for building services.

**Do beam clamps for sprinkler pipework need approval?**

Often, yes. The sprinkler designer or insurer usually specifies listed hangers, for example FM or VdS approved, or LPCB in the UK. Some universal M10 beam clamps carry FM and VdS approval. Check the project specification before ordering.

## Configure it yourself

https://strutconfigurator-app.pages.dev/?lang=en&systeem=trapeze

---

Source: https://strutconfigurator-site.pages.dev/en/knowledge-base/beam-clamp-guide/ · Last updated: 2026-11-19 · Loads are indicative; the manufacturer confirms.
Strutconfigurator is part of NEXTRIQ (Rotterdam).
